Answers about IMER machines and parts

13 answers in Specs and selection

• What engines and motors come on the HSM 6, HSM 8 and HSM 12 mortar mixers?

  Per IMER's product sheet, the towable HSM mixers come as gas or electric models, in steel or poly drum. The HSM 6 (6 cu ft batch) has a Honda GX160, 5.5 hp, or a 1.5 hp…

  Specs and selection · IMER HSM 6 · IMER HSM 8

• What compressor do I need to spray with a Small 50?

  Compressors from 180 to 600 l/min can be used, and in general more air gives a finer spray. A 180 l/min unit suits most products that you spread by hand after spraying…

  Specs and selection · IMER Small 50

• Which deflector size should I use on a Koine 4 spray jet?

  Deflectors are available in 10, 12, 14, 16 and 18 mm. A smaller hole breaks the material up more finely, while a bigger hole copes better with coarser material. IMER…

  Specs and selection · IMER Koine 4

• What are wet mode and dry mode on the Koine 3.1?

  IMER's product sheet describes two ways to run the Koine 3.1. In dry mode, the normal one, you tip bags of dry product such as underlayment, mortar or grout straight…

  Specs and selection · IMER Koine 3.1

• What size diamond disc does the Masonry 750 Plus take, and how do I change it?

  The Masonry 750 Plus uses a disc with a 750 mm (30 in) outside diameter, a 25.4 mm center hole and a maximum thickness of 4 mm. A 700 mm disc can also be fitted, but…

  Specs and selection · IMER Masonry 750 Plus

• What blade size and arbor does each Combicut tile saw take?

  Per IMER's product sheets: the Combicut 200 VA takes an 8 in blade, the Combicut 250 VA, 250/1000 VA and 250/1500 VA take 10 in blades, and the Combicut 350 iPower…

  Specs and selection · IMER Combicut 200 VA · IMER Combicut 250 VA

• Which IMER diamond blade type should I use for tile, brick or concrete?

  IMER's blade page sorts its blades by job. Continuous-rim blades suit ceramic tile, porcelain and stone and give the cleanest, most accurate cut: 8 in (1193920), 10 in…

  Specs and selection · IMER Combicut 350 iPower · IMER Masonry 750 Plus

• Which Combicut model do I need for large-format tile?

  Pick the model by cutting length. IMER's sheets list the maximum cut length, with plunge cut in brackets: Combicut 200 VA 21 in (24 in); Combicut 250 VA 28 in (31 in)…

  Specs and selection · IMER Combicut 200 VA · IMER Combicut 250 VA

• What motor options does the Mix 750 come with?

  Per IMER's product sheet the Mix 750 comes as a 240 V, 5 hp single-phase electric (1194644); a 208 V, 7.5 hp three-phase (1194645); a 480 V, 7.5 hp three-phase…

  Specs and selection · IMER Mix 750

• What are the main specs of the Mix 360 Plus?

  From IMER's product sheet, the Mix 360 Plus is a towable vertical shaft paddle mixer with a 12 cu ft drum and a 9 cu ft batch output. The electric model (1194662) uses…

  Specs and selection · IMER Mix 360 Plus

• What does the Mix-All 60 mix, and what size batch does it handle?

  The Mix-All 60 (1193988) is a light, portable paddle mixer used for mortar, stucco, thin set, dry pack, epoxy and plaster, and it also handles rubber materials…

  Specs and selection · IMER Mix-All 60

• What are the differences between the Workman II 250, 350 and 350ED?

  Per IMER's product sheet, all three are towable barrel mixers with a Honda GX160, 5.5 hp gas engine, steel box frame, torsion bar suspension, forklift pockets and a…

  Specs and selection · IMER Workman II 250 · IMER Workman II 350

• What are the key specs of the Booster 20 diesel concrete pump?

  Per IMER's product sheet the Booster 20 is a compact, towable diesel piston pump with a 2-cylinder system, hydraulic control and an S valve. It has a 3-cylinder diesel…

  Specs and selection · IMER Booster 20