Skip to content
IMER PartsUSA

Any format works

Type the number from your parts book, the way it is printed, or a machine name.

  • 3237223
  • 3237-223
  • IMER 3237 223
  • Mix 750

Browse by machine

IMER PartsUSA
Call +1 (307) 301-7723

Mon–Fri 8 am–6 pm, Sat 9 am–1 pm (Mountain Time)

Troubleshooting

IMER Mix 360 problems and fixes

The troubleshooting table of the IMER manual 3211378 R02, problem by problem: the likely causes, what the manual says to do and the parts for each fix.

problems
8
Disconnect the machine from power before any check. Fixes marked Qualified person involve electrical, pressure or engine work: have them done by a qualified technician and follow the safety instructions in your IMER manual.
  1. (MIXER WITH ELECTRIC MOTOR) The motor does not start when switched on.
    Possible causeWhat to do
    No power in the supply lineCheck the line
    The electric plug and socket are not connected properlyMake a proper connection
    The cable from the plug to the electric panel is brokenReplace the cable
    A wire has become disconnected inside the panelRe-make the connection
    A wire has become disconnected on the motor terminal boardRe-make the connection
    The pushbutton is faulty.Replace the pushbutton.
    The protective cover is openClose it
    The limit switch is faultyReplace it
    A wire has become disconnected inside the limit switchRe-make the connection

    Qualified person: this fix involves electrical, pressure or engine work.

    Parts named in these fixes, from the Mix 360 parts book

    Check the part number on your machine or in its parts book before you order.

    Source: IMER manual 3211378 R02, page 6

  2. The endothermic motor does not start
    Possible causeWhat to do
    -See motor manual

    Qualified person: this fix involves electrical, pressure or engine work.

    Source: IMER manual 3211378 R02, page 6

  3. The discharge outlet leaks water
    Possible causeWhat to do
    The sealing gasket is wornReplace the rubber
    The spring is broken or ineffectiveReplace the spring

    Source: IMER manual 3211378 R02, page 6

  4. Scraper rubbers do not mate with the tank
    Possible causeWhat to do
    Worn rubbersReplace the rubbers and/ or adjust their position (11.3 MIXING PADDLE REPLACEMENT)

    Source: IMER manual 3211378 R02, page 6

  5. The outlet will not open
    Possible causeWhat to do
    Deposit in the outlet protectorRemove and clean the outlet(11.2 REMOVAL OF TANK PROTECTION COVER)

    Source: IMER manual 3211378 R02, page 6

  6. During mixing, the paddle rpm decreases or paddles stop
    Possible causeWhat to do
    Belts are slack and are slippingTension the belts(11.4 TENSIONING AND REPLACING TRANSMISSION BELTS)

    Parts named in these fixes, from the Mix 360 parts book

    Check the part number on your machine or in its parts book before you order.

    Source: IMER manual 3211378 R02, page 6

  7. Water does not arrive at the tank
    Possible causeWhat to do
    There is no water in the feed lineChange the feed line
    Water hose or valve blockedClean the hose or valve

    Source: IMER manual 3211378 R02, page 6

  8. The blades do not stop when the protection cover is raised
    Possible causeWhat to do
    Limit switch not mounted correctlyAdjust position of limit switch (11.1)
    Cam not mounted correctlyRefer to limit switch adjustment instructions (11.1)

    Qualified person: this fix involves electrical, pressure or engine work.

    Parts named in these fixes, from the Mix 360 parts book

    Check the part number on your machine or in its parts book before you order.

    Source: IMER manual 3211378 R02, page 6

IMER Mix 360 partsAsk a parts specialist